Click here for Knife installation guide.

Click here for Rangefinder installation guide.

How to Apply GunWraps' Binocular Vinyl Gun Wrap Skin

Step 1 - Cleaning: Before wrapping your binoculars, it is vital to thoroughly inspect, prep, and clean the surfaces being wrapped. 

Isopropyl alcohol should be used to remove any residue on the surfaces to be wrapped. Wrapping your binoculars with your bare hands may add natural oil or grease to surface, so we recommend washing your hands with dish soap after cleaning your binoculars prior to installation.

Step 2: Look at the pre cut pieces included in your kit. There will be two large rectangular parts (one for each side). Take your time removing pieces from the backing of the sheet as they can tear. 

Step 3: Place your binoculars over sheet and trim off any excess film from the bottom of the part that will not be needed for your particular model. Be sure to leave at least 1" of extra film to ensure that the entire surface will be covered. Remove film from the kit and align center of part to the center of the side of the binoculars. There is a v notch cut into the part to help locate the center.

 

Step 4:  Thoroughly work film onto the surface of the binoculars. Use heat when necessary to stretch and help film to conform to the shapes of the surface. It is recommended to use a wrap glove or squeegee to carefully apply film to surface to avoid any bubbles or wrinkles. If bubbles or wrinkles do occur, simply lift vinyl and give a short burst of heat to film to bring back to original shape and re apply. Allow film to cool then trim any excess film. Once entire part is wrapped and trimmed, apply heat and firm pressure on all wrapped surfaces, this will solidify the bond between the film's adhesive and the surface of your binoculars.

 

Repeat Steps 3 and 4 for opposite side. 

 

Step 5:  Enjoy your new wrap!

How to Apply GunWraps' Rangefinder Vinyl Gun Wrap Skin

Step 1 - Cleaning: Before wrapping your rangefinder, it is vital to thoroughly inspect, prep, and clean the surfaces being wrapped. 

Isopropyl alcohol should be used to remove any residue on the surfaces to be wrapped. Wrapping your rangefinder with your bare hands may add natural oil or grease to surface, so we recommend washing your hands with dish soap after cleaning your binoculars prior to installation.

Step 2: Look at the pre cut piece included in your kit. Take your time removing piece from the backing of the sheet as it can tear. 

Step 3: Place your rangefinder over the sheet and trim off any excess film from the part that will not be needed for your particular model. Be sure to leave at least 1" of extra film to ensure that the entire surface will be covered. Remove film from the kit and align center of part to the center of the side of top of the rangefinder. There is a v notch cut into the part to help locate the center.

 

Step 4:  Thoroughly work film onto the surface of the rangefinder. Use heat when necessary to stretch and help film to conform to the shapes of the surface. It is recommended to use a wrap glove or squeegee to carefully apply film to surface to avoid any bubbles or wrinkles. If bubbles or wrinkles do occur, simply lift vinyl and give a short burst of heat to film to bring back to original shape and re apply. Allow film to cool then trim any excess film. Once entire part is wrapped and trimmed, apply heat and firm pressure on all wrapped surfaces, this will solidify the bond between the film's adhesive and the surface of your binoculars.

 

 

Repeat Step 4 for opposite side

 

Step 5: Enjoy your new wrap!

 

Step 1 - Cleaning: Before wrapping your Knife , it is vital to thoroughly inspect, prep, and clean the surfaces being wrapped. 

Isopropyl alcohol should be used to remove any residue on the surfaces to be wrapped. Wrapping your knife with your bare hands may add natural oil or grease to surface, so we recommend washing your hands with dish soap after cleaning your knife prior to installation.

How to Apply GunWraps' Knife Vinyl Gun Wrap Skin

Step 2: Look at the pre cut pieces included in your kit. There will be one large rectangular parts. 
Step 3: Place your knife over sheet and trim off any excess film from the bottom of the part that will not be needed for your particular model. Be sure to leave at least 1" of extra film to ensure that the entire surface will be covered. Remove film from the kit and align center of part to the center of the side of the knife. There is a v notch cut into the part to help locate the center.
Step 4:  Thoroughly work film onto the surface of the knife. Use heat when necessary to stretch and help film to conform to the shapes of the surface. It is recommended to use a wrap glove or squeegee to carefully apply film to surface to avoid any bubbles or wrinkles. If bubbles or wrinkles do occur, simply lift vinyl and give a short burst of heat to film to bring back to original shape and re apply. Allow film to cool then trim any excess film. Once entire part is wrapped and trimmed, apply heat and firm pressure on all wrapped surfaces, this will solidify the bond between the film's adhesive and the surface of your knife.

Repeat Steps 3 and 4 for opposite side. 

Step 5:  Enjoy your new wrap!

Zachary Spezia